SITE MAP | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RANGE-N NEETER DRIVE BEVEL GEARBOXES
|
The Neeter Drive gearbox is an ultra compact unit and is available in 5 sizes and 5 gear ratios. The design employs a central bearing housing support on the 1:1 and 1.5:1 gear ratios, and a small extended bearing housing on the input side of the gearboxes with ratios 2:1 and above and hollow shaft output. It is a high torque rated unit with good thermal characteristics. It is available in solid shaft and hollow output shaft configurations and has the option of a motor mounting flange, for easy direct coupling of a standard electric motor.
Housing
S.G. Iron to BS27789:1985, Grade 420/12.
Gears
All gears are made from alloy steel and case hardened.
Bearings
Pinion (input) and gear shaft (output) are fitted with twin taper roller bearings to provide almost unchanged backlash over a long life.
Sealing
All units are fitted with spring energized single lipped oil seals and all flanges are sealed O-rings.
Lubrication
Lubrication is dependent upon the operating conditions, oil for higher speeds and semi fluid grease for medium and low speeds.
Note: All units are shipped dry from the factory and should be lubricated before use.
Service Life
Life of gears including mountings 10,000 hours.
Efficiency
Reduction ratio bevel gear units are approximately 95% - 98% efficient. Please consult Neeter Drive regarding increasing ratios.
Overhung loads
All units are rated for in-line connection. If a unit is to be fitted with a belt pulley, chain sprocket etc., radial forces must be considered. If in doubt please consult Neeter Drive.
Note: Where operating conditions deviate from those described above please consult Neeter Drive.
Gear Unit |
Ratio |
Power Ratings at given Input Speeds (rev min –1) |
Models |
|||||||
50 |
250 |
500 |
750 |
|||||||
kW |
Nm |
kW |
Nm |
kW |
Nm |
kW |
Nm |
|||
Series 35 |
1:1 |
0.4 |
75 |
1.7 |
63 |
3.1 |
58 |
4.3 |
54 |
|
1.5:1 |
0.2 |
56 |
0.7 |
39 |
1.4 |
39 |
2.1 |
39 |
||
2:1 |
0.12 |
45 |
0.5 |
37 |
0.9 |
34 |
1.2 |
30 |
||
3:1 |
0.03 |
17 |
0.15 |
17 |
0.31 |
17 |
0.45 |
17 |
||
Series 37 |
1:1 |
1.0 |
187 |
4.3 |
161 |
7.7 |
144 |
10.8 |
135 |
|
1.5:1 |
0.5 |
140 |
1.9 |
107 |
3.5 |
98 |
5.0 |
94 |
||
2:1 |
0.3 |
112 |
1.3 |
97 |
2.5 |
94 |
3.5 |
87 |
||
3:1 |
0.11 |
62 |
0.5 |
56 |
0.8 |
45 |
1.2 |
45 |
||
4:1 |
0.06 |
45 |
0.2 |
30 |
0.4 |
30 |
0.6 |
30 |
||
Series 38 |
1:1 |
2.5 |
468 |
11.7 |
438 |
21.2 |
397 |
29.9 |
373 |
|
1.5:1 |
0.9 |
253 |
3.4 |
191 |
6.1 |
171 |
8.7 |
163 |
||
2:1 |
0.6 |
225 |
2.6 |
195 |
4.8 |
180 |
6.9 |
172 |
||
3:1 |
0.3 |
168 |
1.2 |
135 |
2.2 |
124 |
3.1 |
116 |
||
4:1 |
0.13 |
97 |
0.7 |
105 |
0.9 |
67 |
1.3 |
65 |
||
Series 39 |
1:1 |
5.0 |
936 |
22.2 |
831 |
38.6 |
723 |
52.0 |
649 |
|
1.5:1 |
1.7 |
477 |
9.0 |
505 |
18.9 |
531 |
29.2 |
547 |
||
2:1 |
2.0 |
749 |
7.9 |
591 |
14.5 |
543 |
20.7 |
517 |
||
3:1 |
0.8 |
449 |
3.2 |
359 |
5.9 |
331 |
8.4 |
314 |
||
4:1 |
0.4 |
299 |
1.74 |
261 |
2.9 |
217 |
4.2 |
210 |
||
Series 40 |
1:1 |
16.2 |
3032 |
74.3 |
2781 |
126 |
2358 |
166 |
2071 |
|
1.5:1 |
8.9 |
2499 |
36.4 |
2044 |
65.6 |
1842 |
90.8 |
1700 |
||
2:1 |
6.8 |
2546 |
28 |
2096 |
52.0 |
1947 |
74.8 |
1867 |
||
3:1 |
2.6 |
1460 |
10.3 |
1157 |
19.2 |
1078 |
27.8 |
1042 |
||
4:1 |
1.5 |
1123 |
6.9 |
1033 |
11.7 |
876 |
16.9 |
844 |
Gear Unit |
Ratio |
Power Ratings at given Input Speeds (rev min –1) |
Models |
|||||||
1000 |
1500 |
2000 |
3000 |
|||||||
kW |
Nm |
kW |
Nm |
kW |
Nm |
kW |
Nm |
|||
Series 35 |
1:1 |
5.4 |
51 |
7.4 |
46 |
8.9 |
42 |
10.4 |
32 |
|
1.5:1 |
2.6 |
37 |
3.7 |
35 |
4.7 |
33 |
5.6 |
26 |
||
2:1 |
1.6 |
30 |
2.2 |
27 |
2.9 |
27 |
3.6 |
22 |
||
3:1 |
0.6 |
17 |
0.9 |
17 |
1.2 |
17 |
1.6 |
15 |
||
Series 37 |
1:1 |
13.6 |
127 |
18.5 |
115 |
22.6 |
106 |
30.6 |
95 |
|
1.5:1 |
6.4 |
90 |
9.0 |
84 |
11.5 |
81 |
17.0 |
80 |
||
2:1 |
4.5 |
84 |
6.4 |
80 |
8.1 |
76 |
12.0 |
75 |
||
3:1 |
1.5 |
42 |
2.1 |
39 |
2.8 |
39 |
4.2 |
39 |
||
4:1 |
0.8 |
30 |
1.2 |
30 |
1.5 |
28 |
2.25 |
28 |
||
Series 38 |
1:1 |
38 |
356 |
52.6 |
328 |
65.1 |
305 |
- |
- |
|
1.5:1 |
11.1 |
156 |
15.5 |
145 |
19.4 |
136 |
27.6 |
129 |
||
2:1 |
9.0 |
168 |
12.8 |
160 |
16.6 |
155 |
24.6 |
153 |
||
3:1 |
4.0 |
112 |
5.7 |
107 |
7.5 |
105 |
11.2 |
105 |
||
4:1 |
1.7 |
64 |
2.4 |
60 |
3.2 |
60 |
4.8 |
60 |
||
Series 39 |
1:1 |
62.9 |
589 |
77.2 |
482 |
- |
- |
- |
- |
|
1.5:1 |
39.9 |
560 |
61.5 |
576 |
83.2 |
584 |
- |
- |
||
2:1 |
26.6 |
498 |
38.0 |
474 |
49.5 |
463 |
76.3 |
476 |
||
3:1 |
10.9 |
306 |
15.6 |
292 |
20.5 |
288 |
30.3 |
284 |
||
4:1 |
5.4 |
202 |
7.7 |
192 |
10.2 |
191 |
15.3 |
191 |
||
Series 40 |
1:1 |
194 |
1816 |
- |
- |
- |
- |
- |
- |
|
1.5:1 |
112 |
1572 |
145 |
1357 |
- |
- |
- |
- |
||
2:1 |
96.7 |
1810 |
139 |
1735 |
181 |
1694 |
- |
- |
||
3:1 |
36.1 |
1014 |
52.0 |
973 |
68.3 |
959 |
102 |
955 |
||
4:1 |
21.9 |
820 |
31.6 |
789 |
42.1 |
788 |
62.8 |
784 |
Rating within the bordered area – check thermal limit
For more information refer to catalogue